jackson@vistamatt.com +1 619 558 6563 Technical documents Request a sample

Home/News/Technical Insight

Precipitated Silica Matting Agents: Structure, Performance and Selection

Two precipitated silica matting agents can share a CAS number and a median particle size yet behave very differently in the same resin. This article links each structural level to a measurable behaviour and turns it into a practical way to select a grade.

A precipitated silica matting agent is a porous, synthetic amorphous silica powder that lowers gloss by creating fine roughness at the surface of a cured film. Two grades can share a chemical formula, a CAS number and even a median particle size, yet behave very differently in the same resin. The difference lies in structure: how the particles are built, how open their pores are, how wide the size distribution is and what sits on their surface. This article looks at those structural levels, links each one to a behaviour you can measure in the lab, and turns that into a practical way to select a grade.

What "structure" means in precipitated silica

Precipitated silica is built in layers, and each layer matters for a different reason:

  • Primary particles are the very small silica units that form during precipitation. Their size and how tightly they pack set the specific surface area.
  • Aggregates are primary particles fused into a rigid, porous framework. The spaces inside this framework give the pore volume that makes silica so light per particle.
  • Agglomerates and the milled particle are what you actually add to the coating: aggregates held together and then milled and classified to a target size distribution.
  • The surface carries silanol groups and, on treated grades, a wax or organic layer that changes how the particle meets the binder.

Datasheets describe these levels indirectly. On the Vistamatt technical data sheets, particle size (laser diffraction, ISO 13320) describes the milled particle, BET surface area and pore volume describe the internal structure, oil absorption (DBP method) reflects both structure and surface, and loss on ignition reflects the level of surface treatment. All Vistamatt grades are synthetic amorphous silica (precipitated), CAS No. 7631-86-9, so the differences between grades come from these structural variables rather than from a change of material.

Structure and matting efficiency

Matting comes from particles near the top of the film creating micrometre-scale roughness as the film shrinks. Two structural features decide how much roughness a given weight of silica can create.

Particle size relative to film thickness. Larger particles protrude more readily and reach lower gloss at the same loading, while finer particles give a smoother, more refined surface but need more material for the same gloss drop. That is why the Vistamatt industrial range steps up in size from VS361C (6.2–6.5 µm) through VS381C (8.0–8.3 µm) to VS391C (9.0–9.5 µm) for progressively lower gloss targets, while spray-applied UV wood work leads with the finer VS141S (3.8–4.0 µm).

Pore volume. A particle with a more open internal structure weighs less, so the same weight of powder contains more particles. Higher pore volume therefore usually means more matting per gram. Across the Vistamatt range, pore volume runs from about 1.2–1.5 mL/g (VS3550U) to 1.6–1.9 mL/g (VSKD721), with most waterborne, deep matte and industrial grades at 1.6–1.8 mL/g and the flexible and soft-touch grades at 1.3–1.6 mL/g.

The practical consequence is that equal weight is not equal matting. When you compare two precipitated silica matting agents, compare them at equal gloss as well as at equal loading.

Structure and viscosity

A porous particle takes up liquid into its pores and onto its surface, and that liquid is no longer available to keep the formulation fluid. Oil absorption is the quickest datasheet guide to this effect, and it can vary a lot between grades of similar size.

Compare two roughly 7 µm grades on the Vistamatt data sheets: VS171S (7.0–7.5 µm) has an oil absorption of 310–320 mL/100 g, while VS370U (7.0–7.3 µm) sits at 180–200 mL/100 g. Similar particle size, very different expected impact on viscosity. The UV roller lead grade VS3550U goes further, at 140–160 mL/100 g, which is the kind of profile chosen when a 100% solids or high-solids UV system has little room for thickening. At the other end, the soft-touch grade VS3851 sits at 340–360 mL/100 g.

BET surface area is related, but it is not a stand-alone predictor. VS3550U combines the highest BET in the range (500–600 m²/g) with the lowest oil absorption, alongside a higher loss on ignition (12.65%). Surface treatment and pore structure both shape how much liquid a particle actually ties up, so read BET, oil absorption and loss on ignition together rather than one at a time.

Structure, clarity and surface appearance

In clear coats the matting agent has to disappear optically. Amorphous silica has a refractive index close to that of many binders, which is a large part of why it is the default for clear wood and plastic finishes. Structure still affects what you see:

  • The coarse tail of the size distribution, not the median alone, decides whether a thin film looks clean or shows specks and seeds. Ask how the distribution is controlled, not only what the d50 is.
  • Dispersibility matters because undispersed agglomerates scatter light like oversized particles. Grades that wet out easily give more consistent haze and gloss from batch to batch at the same mixing energy.
  • Surface treatment can help particles sit evenly in the film, which supports uniform gloss across large panels.

For high-clarity waterborne clear coats, the Vistamatt lead grade is VS660 (5.0–5.3 µm), with VS651 (4.9–5.2 µm) as a finer comparison where smoothness and feel lead the brief.

Surface chemistry: treated and untreated precipitated silica

An untreated precipitated silica surface is covered in silanol groups. These interact with polar binders and with each other, which can help build structure in the liquid coating but can also contribute to hard settling in low-viscosity systems. A wax or organic surface treatment changes that interaction. In general terms, treatment is used for softer settling and easier redispersion, better scratch and burnish behaviour, a smoother feel, and in some systems lower thickening.

Loss on ignition is the simplest datasheet indicator of treatment level. VS651 (4.48%) and VS660 (8.25%) have similar size, BET and pore volume but different surface chemistry. Several UV wood grades sit higher still: VS370U at 11.45%, VS3550U at 12.65% and VS6907 at 14.35%. Treatment is not automatically an upgrade: in some resins it can affect intercoat adhesion or recoatability, so test it in your own system.

How to select a precipitated silica matting agent

Selection is easiest when you work from the constraint that is hardest to move in your formulation:

  1. Viscosity is tight (UV, high-solids, spray limits): shortlist grades with lower oil absorption and check the treatment level, then confirm gloss efficiency.
  2. Clarity or surface refinement leads (clear wood, piano-type finishes, thin films): favour finer, readily dispersible grades and look closely at the coarse end of the distribution.
  3. Low gloss at low addition (industrial, coil, deep matte): favour larger particle size and higher pore volume, and check feel and settling.
  4. Feel and flexibility (soft-touch, leather): consider grades built for those systems, where pore volume and treatment are tuned for flex and hand rather than for maximum efficiency.

Then define the film: resin type, cure method, dry film thickness, application method and the gloss target with its measuring angle. The grade selector uses those inputs to suggest a lead grade and a comparison grade.

What to test before you commit

  • Gloss at the right angle, usually 60°, and 85° when 60° readings are very low, across a short loading ladder for each grade.
  • Viscosity right after dispersion and again after storage, since structure-driven thickening can develop over time.
  • Fineness of grind and appearance in a draw-down at your real film thickness, checking for specks, haze and gloss uniformity.
  • Settling and redispersion after storage, especially for untreated grades in thin systems.
  • Surface performance: feel, scratch and burnish resistance, and recoatability where it applies.

Keep dispersion time and energy fixed across samples, and always run your current control alongside. If you would like samples for a screening round, you can request them through the contact page; Vistamatt asks for the resin type, target gloss, application method and current problem first, so each sample arrives with a screening plan.

Grade recommendations are a starting point for screening. Final suitability, dosage and performance must be verified in the customer's own resin system, at the target gloss and under actual process conditions.