jackson@vistamatt.com +1 619 558 6563 Technical documents Request a sample

Home/News/Technical Insight

Synthetic Amorphous Silica as a Matting Agent: Why It Dominates Gloss Control

Synthetic amorphous silica carries most of the gloss control in modern coatings. Here is what makes the material so effective, how to read its datasheet, and where its limits lie.

Walk through the matting agents on almost any coatings formulator's shelf and most of them will be the same material: an amorphous silica matting agent. Waxes, polymer beads and mineral fillers all have their place, but synthetic amorphous silica (SAS) carries the bulk of gloss control in wood finishes, industrial coatings, leather, inks and plastics films. This article looks at why — what "amorphous" actually means, which properties of the material make it so effective, and where its limits are.

What "amorphous" means, and why it matters

Silicon dioxide exists in crystalline forms, such as quartz, and in non-crystalline (amorphous) forms. In an amorphous silica the SiO2 network has no long-range order: the particles are built from small primary units that aggregate into a porous, sponge-like structure. Matting grades are produced synthetically, under controlled conditions, rather than mined.

The distinction matters in two ways. Technically, the amorphous, porous structure is what gives a matting silica its low density, high pore volume and large internal surface area — the properties that drive matting efficiency. Practically, amorphous and crystalline silica are treated very differently in occupational health and regulatory terms, so buyers should be clear about which they are specifying. Always confirm the classification and handling advice in the supplier's safety data sheet for the specific grade.

Synthetic amorphous silica is made by several routes — precipitation, gel processes and flame (fumed) processes. Precipitated and gel silicas are the main families used for matting; fumed silica is more often used for rheology control. Our earlier article on precipitated silica matting agents covers the precipitated route in detail.

How amorphous silica reduces gloss

Gloss is specular reflection from a smooth surface. A matting agent works by creating micro-roughness at the film surface so that incoming light is scattered rather than reflected in a single direction. As a coating dries or cures, the film shrinks around the silica particles and leaves a fine, irregular topography. The more effectively that topography forms, the lower the measured gloss at a given addition level.

Amorphous silica is particularly good at this for three reasons:

  • High porosity, low density. A porous particle gives a lot of volume per kilogram, so a modest weight addition places many particles in the film. Pore volume across the Vistamatt range is 1.2–1.9 mL/g.
  • Controllable particle size. Synthetic production allows the particle size distribution to be set for the film build and target gloss. Vistamatt grades run from 2.1–2.4 µm (laser diffraction, ISO 13320) up to 9.0–9.5 µm.
  • Irregular particle shape. Aggregated, irregular particles scatter light more efficiently than smooth spheres of the same size.

Clarity: the property other matting agents struggle to match

For clear coats the challenge is not just lowering gloss but doing it without a milky or grey appearance. Here amorphous silica has a natural advantage: its refractive index is close to that of many common binders, such as acrylics and polyurethanes. When the refractive indices of particle and resin are similar, the particle scatters less light inside the film, so transparency and depth of colour over dark substrates are better preserved.

Clarity still depends heavily on grade choice. Finer particles and a well-designed surface treatment generally help, as does good dispersion. The waterborne grades in our range — VS351C, VS651, VS660, VS1531D and VS6550, all 4.8–5.6 µm — use a surface treatment optimised for high-clarity clear coats. See waterborne clear wood for how those grades are applied.

Chemical stability and broad compatibility

Amorphous silica is chemically inert in nearly all coating systems. It does not react with binders, crosslinkers or most additives, and it tolerates the conditions found in solvent-borne, waterborne, UV-curable, high-solids and powder systems. That inertness is a large part of why one material family can cover so many applications.

Compatibility is then fine-tuned through the surface. Untreated silica has a hydrophilic, silanol-rich surface; treated grades carry an organic surface treatment (commonly wax or polymer based) that improves wetting, reduces hard settling and can improve scratch and burnish resistance. On a datasheet, loss on ignition (LOI) is a useful indicator of treatment level. Across the Vistamatt range LOI runs from about 4.4% on lightly treated grades to 14.35% on VS6907, a UV wood grade.

Reading an amorphous silica datasheet

Because the base material is the same, the differences between grades come down to a handful of measurable properties. The Vistamatt technical data sheets report the following for every grade:

  • Particle size (µm): the main lever for matting efficiency versus surface smoothness. Coarser grades matt more strongly and suit thicker films; finer grades give a smoother feel and better clarity in thin films.
  • BET surface area (m²/g): internal surface measured by nitrogen adsorption. Our range spans 170–600 m²/g; VS3550U, for example, sits at 500–600 m²/g.
  • Oil absorption (mL/100 g, DBP): correlates with structure and with the grade's effect on viscosity. Values in our range run from 140–160 (VS3550U) to 340–360 (VS3851).
  • Pore volume (mL/g): higher pore volume generally means more efficient gloss reduction at a given particle size, and a greater influence on viscosity.
  • Loss on ignition and moisture: surface treatment level and drying condition. Excess moisture causes agglomeration and hard-packing in storage.

No single number predicts performance on its own. Two grades with similar particle size can behave quite differently in viscosity, settling and clarity because of differences in structure and surface treatment.

Where amorphous silica is not the whole answer

Silica dominates gloss control, but it is not always used alone. Some practical limits to keep in mind:

  • Viscosity build. High-structure grades raise viscosity, which can limit addition level in high-solids or spray systems.
  • Settling. Dense, coarse particles in low-viscosity systems can settle; surface treatment and particle size distribution help but do not remove the need for good formulation practice.
  • Burnish and scratch marks. Highly matt films can polish up under rubbing. Treated grades, or combinations with waxes, are often used where this is a concern.
  • Haptics. For pronounced soft-touch effects, silica is frequently combined with other additives; dedicated grades such as VS370T and VS3851 are used in flexible and soft-touch coatings.

Choosing a grade

A sensible starting point is to define the system (resin chemistry and application method), the dry film thickness, the target gloss and geometry (for example 60° or 85°), and whether clarity, feel or burnish resistance is the priority. That narrows the choice to a family — UV wood, waterborne clear, industrial and metal, leather, deep matte or soft-touch — before you compare individual grades. The grade selector walks through those questions.

Then screen at least two candidates side by side in your own formulation, at the same addition level, measuring gloss, viscosity, clarity over a dark substrate and storage behaviour. Vistamatt evaluation samples ship with a screening plan matched to your resin system, target gloss and application method — tell us about your system to request one.

Grade recommendations are a starting point for screening. Final suitability, dosage and performance must be verified in the customer's own resin system, at the target gloss and under actual process conditions.