Wax-Treated Silica Matting Agents vs Untreated: When Surface Treatment Pays Off
Wax treatment does not change how silica lowers gloss, but it changes settling, surface feel, burnish resistance and viscosity. Here is when it earns its place, when untreated silica is the better baseline, and how to screen the two.
A wax-treated silica matting agent is a precipitated or amorphous silica whose particles carry a thin wax layer applied after the silica is made. The core job is the same as for an untreated grade: particles near the surface of the drying film create micro-roughness that scatters light and lowers gloss. What the wax changes is everything around that job: how the powder settles in the can, how the cured surface feels and resists burnishing, and how much the silica thickens the liquid coating. This article sets out when that treatment is worth specifying, when an untreated grade is the better choice, and how to tell the two apart on a datasheet.
What surface treatment actually changes
Untreated silica presents a surface covered in silanol groups. Those groups interact with each other and with polar components in the formulation, which is part of why untreated silica builds viscosity and why particles that settle can pack together firmly. A wax after-treatment coats part of that surface. The practical consequences formulators usually look for are:
- Softer settling. Treated particles tend to form a loose sediment that stirs back in, rather than a hard cake at the bottom of the drum.
- Surface feel and mar behaviour. Wax at the film surface lowers friction, which can improve burnish and scratch resistance and give a smoother hand.
- Lower thickening in some systems. Because fewer silanol groups are free to interact, a treated grade can add less viscosity than an untreated grade of similar particle size.
- Dispersion. Treatment can make wetting easier in certain resins, which matters on lines with limited dispersion energy.
None of these effects is universal. The size of each depends on the resin, the solvent or water phase, the additive package and the cure. That is why surface treatment is a selection variable to screen, not a box to tick.
Where untreated silica still wins
Untreated grades are simpler and often more efficient per unit added. With no organic layer, the full pore structure is available to interact with the binder, and there is no wax that could migrate, affect recoat adhesion or interfere with a sensitive cure. In systems where clarity on dark substrates is the binding constraint, or where the formulation already carries a slip and mar package, the extra cost and complexity of treatment may buy little.
The industrial route illustrates this. On the industrial and metal coatings page, VS171S (7.0–7.5 µm) is the usual first screen at 2–5 % on total formulation, and the TS 100 cross-reference positions it on an untreated route. Coil and equipment topcoats run at high film build through a fast bake, so grade selection there favours efficient gloss reduction and robust structure. If burnish resistance turns out to be the weak point, the first response is often the binder or additive package rather than the matting agent itself.
When a wax-treated silica matting agent pays off
Treatment tends to earn its place when one of the following is the real problem:
- Hard settling in storage or in the line tank. If a batch needs heavy re-dispersion after a few weeks, or a ring tank shows a hard sediment, a treated grade is one of the most direct fixes.
- Burnish and polishing marks. Furniture, panel and leather finishes that are handled, stacked or rubbed show glossy patches where matting particles are flattened or pulled out. Wax at the surface reduces the friction that causes this.
- Feel. When the specification includes a smooth or silky hand, treatment is often part of reaching it.
- Viscosity headroom. In high-solids and 100 % solids UV systems there is little room for the thickening that a high-structure untreated silica brings. A treated grade can let you reach the gloss target at application viscosity.
UV wood and panel coatings combine several of these at once, which is why treated grades are common there. On Vistamatt's technical data sheets, the S-series grades for UV wood, VS141S and VS641, are described as surface-treated for dispersion in UV-curable acrylate systems with minimal viscosity impact. VS141S sits at 3.8–4.0 µm, with BET surface area 240–270 m²/g and oil absorption 280–300 mL/100 g, and is the fine route for UV spray appearance and surface refinement.
Reading treatment level on a datasheet
Most datasheets do not state the treatment chemistry in detail, but they usually give a number that tracks it: loss on ignition (LOI). Calcination burns off bound organics, so a higher LOI generally indicates a more heavily treated surface. On the Vistamatt TDS, LOI runs from about 4.4–4.6 % on grades such as VS171S (4.37 %), VS141S (4.56 %) and VS361C (4.46 %), up to 8.25 % for VS660, 10.46 % for VS1650A, 11.45 % for VS370U, 12.65 % for VS3550U and 14.35 % for VS6907.
Two cautions apply. First, LOI includes bound water and other volatiles, so it is an indicator of treatment level, not a measure of wax content. Second, two grades with similar LOI can carry different treatments. If treatment type matters to your system, for example because of recoat or intercoat adhesion, ask for it to be confirmed in writing for the specific grade before you formulate.
Read LOI alongside the structure figures. Oil absorption and pore volume still predict much of the viscosity and matting efficiency; treatment modifies that behaviour rather than replacing it.
Trade-offs to check before you switch
Treatment solves some problems and can create others. Before committing, check:
- Recoatability and intercoat adhesion. Wax at the surface can reduce adhesion of a following coat. Test sanding and recoat if the finish is part of a multi-coat system.
- Matting efficiency. A treated grade may need a different loading to reach the same gloss. Compare at matched gloss, not matched dosage.
- Clarity. Check haze and transparency on a dark substrate; treatment can shift these in either direction depending on the system.
- Cure interaction. In UV systems, check surface cure at line speed. In 2K and baked systems, check the full cure schedule rather than a lab drawdown alone.
How to screen treated against untreated
The most useful first round runs a treated and an untreated grade at similar particle size against your current control, in your own formulation, with dispersion, film build and cure held constant. For each grade, bracket three loadings around the expected dosage and interpolate to your gloss target. Then compare at that matched gloss on the properties that actually decide the choice: viscosity, settling after storage, burnish and scratch resistance, clarity, feel and recoat.
If the incumbent is a wax-treated product, the cross-reference pages are a useful starting point. For example, the ED 30 alternative page matches VS3550U (5.5–6.0 µm) on the ~5–6 µm route for UV wood and panel roller coatings. A cross-reference is a starting point built on published particle-size data, not a claim that two products are identical; qualification is always done at matched gloss in your system.
Where to start
Start from the problem, not the treatment. If the formulation meets gloss but fails on settling, burnish or viscosity, screen a treated grade. If it fails on efficiency or clarity, or the system is sensitive to recoat adhesion, an untreated grade is usually the better baseline. For UV wood and panel, the UV wood and panel range covers both the fine treated route (VS141S, VS641) and coarser, higher-LOI grades (VS370U, VS3550U, VS6907). Send your resin system, target gloss, application method and film build, and Vistamatt will suggest a grade and starting dosage for the first round, with free 200–500 g samples.