jackson@vistamatt.com +1 619 558 6563 Technical documents Request a sample

Home/News/Technical Insight

What Is a Silica Matting Agent? A Formulator's Complete Guide

A silica matting agent is a porous, synthetic amorphous silica powder that lowers gloss by roughening a coating's surface on a micrometre scale. This guide covers what it is made of, how it is produced, and how to read the five numbers on a datasheet that predict how it will behave in your system.

A silica matting agent is a fine, porous powder of synthetic amorphous silica (SiO2) added to a coating to reduce its gloss. It is the most widely used matting route in wood, industrial, plastic and leather coatings because it lowers gloss efficiently while staying almost invisible inside a clear film.

Most formulators know what a matting agent does. Fewer look closely at what it is, and that is where screening rounds are usually won or lost: two grades with the same median particle size can behave very differently because of their structure and surface treatment. This guide explains the material itself and how to read a datasheet before you open a sample bag.

What a silica matting agent is made of

Chemically, a silica matting agent is silicon dioxide in an amorphous (non-crystalline) form. It is not ground quartz or sand. It is built up synthetically into small particles that are themselves aggregates of much finer primary particles, leaving a network of internal pores. That internal porosity is the reason silica is so efficient: a few percent by weight supplies a very large number of low-density particles.

All Vistamatt grades are synthetic amorphous silica (precipitated), CAS No. 7631-86-9. Crystalline silica content is below 0.1%, verified by XRD, and the material is listed as Active on the TSCA Inventory. Synthetic amorphous silica is not classified as hazardous under GHS; the details for each grade are in the SDS and compliance documents.

How precipitated silica is produced

Precipitated silica is made in water. In outline, a sodium silicate solution is reacted with an acid under controlled temperature, concentration and pH. Silica precipitates out as primary particles that grow and link into porous aggregates. The slurry is then filtered and washed to remove salts, dried, and milled and classified to the target particle size distribution.

Each step leaves a fingerprint on the finished grade:

  • Precipitation conditions set the internal structure: surface area, pore volume and how open the pores are.
  • Milling and classification set the particle size distribution, including the coarse tail that decides whether a thin film looks clean or shows specks.
  • Surface treatment, applied to some grades, changes how the particles interact with the binder, how they settle and how the cured surface feels.

Because Vistamatt makes the silica in-house, these are adjustable process variables rather than fixed properties of a bought-in powder.

Precipitated silica versus other silica types

Matting agents are also made from silica gel, and fumed silica is common in coatings as a rheology additive. In broad terms, silica gels and precipitated silicas are both porous and both used for matting, with differences in pore structure and production route; fumed silica is made at high temperature, has very small primary particles and is mainly used to thicken and control sag rather than to matt. The practical point for a formulator is that the datasheet values, not the production route alone, predict performance.

How to read a matting agent datasheet

A silica matting agent datasheet usually lists five or six values. Here is what each one tells you, with the ranges from the Vistamatt technical data tables as reference points.

Particle size (d50)

The median particle size, measured by laser diffraction (ISO 13320). It is the first lever on gloss and on surface feel. Vistamatt coating grades run from about 2.1–2.4 µm (VS321A, VSKD721) to 9.0–9.5 µm (VS391C), with common workhorse grades such as VS660 at 5.0–5.3 µm. Finer grades suit thin films and spray application; coarser grades reach lower gloss at the same loading but risk a rough feel when the film is thin.

BET surface area

Specific surface area by nitrogen adsorption, in m²/g. Higher surface area generally means stronger interaction with the binder and solvent and a greater effect on viscosity. Most Vistamatt coating grades sit at 200–280 m²/g; for example VS660 and VS1650A are both specified at 250–280 m²/g, and the soft-touch VS3851 at 200–230 m²/g. A few grades sit outside that band, such as VS3550U at 500–600 m²/g.

Oil absorption

Measured by the DBP method in mL/100 g. It correlates with surface area and pore structure, and it is a useful quick predictor of how much a grade will thicken a formulation. Most Vistamatt coating grades fall between about 250 and 320 mL/100 g, with the soft-touch VS3851 higher at 340–360 mL/100 g and some UV grades deliberately lower, such as VS3550U at 140–160 mL/100 g, to keep viscosity down in high-solids systems.

Pore volume

Measured by nitrogen desorption, in mL/g. Higher pore volume usually means more matting per gram, because each particle is lighter and more of them are added at the same weight. The waterborne and deep matte grades sit at 1.6–1.8 mL/g; the flexible and soft-touch grades at 1.3–1.6 mL/g.

Loss on ignition

The weight lost on calcination, in percent. It reflects the level of surface treatment and bound organics, so it is the quickest way to tell a treated grade from an untreated one. Compare VS651 at 4.48% with VS660 at 8.25% and VS6550 at 10.55%: similar particle size and structure, different surface chemistry.

Treated or untreated: what surface treatment changes

Untreated silica is simple and efficient, and it is often the right starting point. Surface treatment, typically wax or organic, is used where the system needs something the bare particle does not give:

  • Soft settling and easy redispersion in storage, instead of a hard-packed layer at the bottom of the can.
  • Scratch, burnish and mar resistance on surfaces that will be handled or cleaned.
  • Smoother feel, which matters on furniture, leather and soft-touch parts.
  • Lower thickening in some systems, which helps high-solids and UV formulations.

Treatment is not automatically better. In some resins it can affect intercoat adhesion or recoatability, so it should be screened in your own system rather than assumed.

Where silica matting agents are used

The same chemistry, tuned by particle size, structure and treatment, covers a wide range of coatings. Vistamatt organises its grades by application rather than by catalogue number:

  • Waterborne clear wood topcoats, where clarity matters as much as gloss (lead grade VS660).
  • UV wood and panel lines, with separate roller and spray paths (VS3550U, VS141S).
  • Industrial, metal and coil coatings (VS171S), deep matte surfaces (VS1650A), flexible and soft-touch systems (VS341S), and leather and synthetic leather (VS131A).
  • Beyond coatings: printing inks, textile coatings and plastic film anti-block.

How to start choosing a grade

Start from the system, not from a single matting figure. The four details that narrow the choice fastest are the resin type, the target gloss and the angle it is measured at, the dry film thickness, and the application method. With those, the grade selector gives a lead grade and a comparison grade to test side by side against your current control.

Judge the result on more than gloss: clarity, surface uniformity, feel, scratch behaviour, viscosity and storage stability all decide whether a grade survives scale-up. Lab samples of 200–500 g are available for qualified coating formulators through the contact page.

Grade recommendations are a starting point for screening. Final suitability, dosage and performance must be verified in the customer's own resin system, at the target gloss and under actual process conditions.