Gloss Reduction in Coatings: The Physics Behind a Matte Film
A matte finish is an optical effect created by surface roughness. Here is how silica matting agents and film formation work together to scatter light away from the gloss meter, and what that means for formulation.
Gloss reduction in coatings looks simple from the outside: add a matting agent, and the shine goes down. Underneath, it is a question of optics and film formation. A surface looks glossy when it returns light as a mirror would, in one direction. It looks matte when that light is spread across many angles. Everything a formulator does to control gloss, from choosing a silica grade to adjusting solvent balance, works by changing how much light leaves the surface in the specular direction. Understanding that physics makes it much easier to predict what a formulation change will do before you spray a panel.
What a gloss meter actually measures
A glossmeter shines a beam onto the film at a fixed angle and measures how much light arrives at a detector placed at the mirror-image angle. The reading, in gloss units (GU), is referenced to a polished black glass standard. Common geometries are 20°, 60° and 85°: 20° separates high-gloss finishes, 60° is the general-purpose angle, and 85° (near grazing) is used to tell low-gloss surfaces apart, where 60° readings bunch together.
The key point is that a glossmeter does not measure "matteness" directly. It measures only the light that leaves in the specular direction. Light that is scattered elsewhere, or absorbed, simply does not register. Gloss reduction is therefore about diverting reflected light away from that one narrow cone.
Why a smooth film reflects like a mirror
At the air–coating interface, a fraction of incident light is reflected according to the Fresnel relationship. For a typical clear binder with a refractive index around 1.5, that fraction is only a few percent at normal incidence and rises steeply toward grazing angles. Most of the light enters the film and is absorbed by a pigment, scattered inside the film, or reflected from the substrate.
If the interface is optically flat, all of that surface reflection travels in one direction, and the gloss reading is high. The binder itself is not "shiny"; the geometry of the surface is what makes it look glossy. This is why the same resin can produce a mirror finish or a dead-flat one, depending only on the topography of the cured film.
Surface roughness: the physics behind a matte film
A matte film is a rough film on a scale comparable to, or larger than, the wavelength of visible light (roughly 0.4–0.7 µm). When the surface carries a population of small bumps and valleys, each local facet reflects light at a slightly different angle. Added together, the reflected light becomes a broad, diffuse lobe instead of a sharp specular beam, and the detector at the mirror angle sees much less of it.
Two features of that roughness matter most:
- Height and slope of the protrusions. Taller, steeper features deflect light further from the specular angle. Very shallow undulations mostly produce haze or a satin sheen rather than true matte.
- Density and uniformity. The surface needs enough features, evenly spread, so that there are few flat areas left to act as small mirrors. Bare patches between particles show up as residual gloss and as visible unevenness.
Because the incident angle changes the effective scale of the roughness, a surface can look quite matte at 60° and still show sheen at 85°. Low-gloss specifications therefore often quote both angles.
How silica creates the roughness
Silica matting agents work by placing particles at the surface of the drying film. As solvent or water leaves, the wet film shrinks. Rigid, porous silica particles do not shrink with it, so the binder pulls down around them and leaves the particles standing proud as micro-protrusions. The final roughness is set by the particle size relative to the dry film thickness, the number of particles per unit area, and how much the film shrinks during cure.
This explains the main levers formulators use:
- Particle size (d50). Larger particles create taller features and stronger gloss reduction per particle, but can feel rough and lower clarity. Finer particles give a smoother, more refined surface at the cost of efficiency. In the Vistamatt range, particle sizes on the technical data sheets run from about 2.1–2.4 µm (VS321A, VSKD721) up to 9.0–9.5 µm (VS391C).
- Pore volume. A high pore volume means a lighter, more voluminous particle, so each gram supplies more particles. Most Vistamatt coating grades list pore volumes between 1.3 and 1.9 mL/g.
- Loading. More particles per unit area means fewer flat zones between them, until the surface is fully covered and extra silica mainly raises viscosity.
- Film shrinkage. Systems that lose a large share of volume on drying, such as many solvent-borne and waterborne lacquers, expose particles more readily. High-solids and 100% solids UV systems shrink much less, so particles tend to stay buried and gloss reduction is harder to achieve.
Film formation decides where the particles end up
The same silica at the same loading can give very different gloss in two formulations because of what happens during drying. If the film skins over quickly, particles may be locked in place before shrinkage pulls the binder down around them. If the film stays open longer, there is more time for the surface to conform to the particles. Solvent blend, flash-off time, film build and cure schedule all shift the result.
UV-curable coatings show this clearly. With little or no solvent to evaporate, there is little shrinkage, so formulators rely on particle selection, surface treatment and process steps to bring silica toward the surface. Vistamatt's UV-oriented S-series grades (VS141S, VS641) are surface-treated for dispersion in acrylate systems with minimal viscosity impact, while the U-series grades (VS370U, VS3550U) are positioned for higher matting efficiency in roller and curtain coating. More detail is on the UV wood and panel page.
Gloss reduction without losing clarity
Scattering at the surface is what we want; scattering inside the film is usually not. In clear coats, the silica that stays in the bulk of the film can make it look grey or milky. Amorphous silica helps here because its refractive index is close to that of many common binders, so particles embedded in the film scatter relatively little light. Haze and loss of depth on dark substrates tend to appear when particles are poorly dispersed, form agglomerates, or are much larger than the film can accommodate.
For waterborne clear wood finishes, Vistamatt lists surface-treated grades such as VS351C, VS651 and VS660 with particle sizes around 4.8–5.3 µm, intended for low haze and good transparency retention. See the waterborne clear wood page for the full set.
Practical consequences for formulators
Putting the physics together gives a few working rules:
- Match particle size to dry film thickness. A particle that is far smaller than the film is likely to be buried; one that is much larger can feel gritty and stand out as a visible defect.
- Disperse to the right level, not the maximum. Under-dispersion leaves agglomerates that scatter inside the film. Very intense grinding can break up porous particles and reduce their matting effect.
- Control the drying process. Changes to film build, flash-off or oven profile can move gloss as much as a change of loading. Keep these fixed when comparing grades.
- Measure at more than one angle. For low-gloss targets, record 60° and 85° together to catch sheen that a single reading would miss.
- Watch stability. Settling during storage changes the effective loading in the can. Surface-treated grades are often chosen partly for better suspension behaviour.
Choosing a starting grade
The physics points to a short decision path. Start with the film: its thickness, how much it shrinks, and whether it is clear or pigmented. That sets the particle size window. Next, decide how important feel, scratch tolerance and clarity are compared with raw efficiency, which guides the choice between untreated, wax-treated and organically treated grades. Finally, run a loading ladder in your own system and read gloss at matched targets.
For very low gloss targets, Vistamatt's deep-matte grades (VS1650A, VS361C) are described for applications requiring gloss below 10 GU at 60°. The grade selector narrows the range by application, and the technical team can suggest a starting point and supply samples for your own panels.