Matting Agents for Coatings: How to Pick the Right Type for Your System
Silica, wax, polymer beads or fillers? The right matting agent for coatings depends on the resin, cure method, film thickness and application. This guide compares the main types and shows how to narrow the choice for your system.
Choosing a matting agent for coatings is rarely about finding the one powder that drops gloss the furthest. It is about matching a matting route to the resin, the cure mechanism, the film thickness and the way the coating is applied, and then checking that clarity, feel, viscosity and storage stability survive the change. This guide walks through the main types of matting agent, what each is good at, and how to narrow the choice for the system in front of you.
How matting agents work
Gloss is specular reflection from a smooth surface. A matting agent lowers it by creating fine, micrometre-scale roughness at the top of the cured film, so that incoming light is scattered in many directions instead of being reflected at a single angle. Most of that roughness forms as the film shrinks during drying or curing: as solvent or water leaves, the binder layer gets thinner and the particles near the surface begin to protrude.
That mechanism explains most of the practical rules formulators work with. Film shrinkage matters, so high-solids and 100% solids systems are harder to matt than low-solids ones. Particle size has to suit the dry film thickness, because a particle much smaller than the film may stay buried while one much larger may feel rough or show as specks. And anything that changes how particles migrate and stay near the surface, such as flow, cure speed or rheology, also changes the gloss you measure.
The main types of matting agent for coatings
Silica matting agents
Synthetic amorphous silica, made by precipitation or as silica gel, is the most widely used matting agent in clear and pigmented coatings. Its internal porosity means each gram contains a large number of low-density particles, so it is efficient at modest loadings, and its refractive index is close to that of many binders, which helps it stay nearly invisible in clear films. Silica is available untreated or with a wax or organic surface treatment that changes settling, feel and scratch behaviour. Our earlier guide, What Is a Silica Matting Agent?, covers the material and its datasheet values in detail.
Wax-based matting agents
Micronised waxes (polyethylene, polypropylene, PTFE-modified and others) are used partly for matting and partly for surface effects such as slip, mar resistance and a smooth hand. On their own they usually give a milder matting effect than silica, and they are often combined with silica rather than replacing it. Wax-treated silica is one way to bring some of those surface benefits into a single additive.
Organic and polymer matting agents
Organic beads and polymer particles (for example polyurea, PMMA or polyurethane types) are chosen where a specific feel, very low gloss in thick films, or a particular optical effect is the priority. They tend to have little effect on viscosity, but matting efficiency per gram, cost and effect on clarity vary widely between products, so they are usually a specialist route rather than a default.
Fillers and extenders
Mineral fillers such as calcium carbonate, talc or barytes lower gloss in pigmented and primer systems as a side effect of their particle size and loading. They are not a substitute for a dedicated matting agent in clear coats, where they would add haze and need much higher loadings to reach the same gloss.
Match the matting agent to the system
Once silica is chosen as the main route, which is the case in most wood, industrial, plastic and leather coatings, the next question is which grade. The system decides more than the gloss target does.
- Waterborne clear coats. Clarity, haze and grain definition are judged as closely as gloss. Fine, readily dispersible grades with a surface treatment suited to clear films are the usual starting point. Vistamatt's lead grade for waterborne clear wood is VS660 (5.0–5.3 µm), with VS651 (4.9–5.2 µm) as the finer, smoother-feel support grade.
- UV-curable coatings. Little or no shrinkage and fast cure make UV systems the hardest to matt, and viscosity limits are tight. Roller and spray lines behave differently enough to need separate screening paths: on the UV wood and panel page, VS3550U leads for roller application and VS141S for spray.
- Industrial, metal and coil coatings. Batch-to-batch consistency, settling resistance and a stable process window matter at volume. Coarser grades reach low gloss at lower additions; VS171S (7.0–7.5 µm) is the first screen, with VS361C, VS381C and VS391C covering progressively lower gloss targets.
- Flexible, soft-touch and leather systems. The matting agent must not crack, whiten or polish when the film bends or is rubbed. Grades such as VS341S for soft-touch finishes and VS131A for leather are chosen for feel and flex as much as for gloss.
- Deep matte surfaces. Below about 10 GU at 60°, the challenge is keeping the surface fine and scratch-tolerant while gloss drops. VS1650A is the lead deep matte route.
Datasheet values that predict behaviour
Within a matting agent family, a handful of numbers on the technical data sheet tell you most of what to expect before you open a sample bag:
- Particle size (d50) sets matting strength and surface feel relative to film thickness. Vistamatt coating grades range from 2.1–2.4 µm (VS321A, VSKD721) to 9.0–9.5 µm (VS391C).
- Oil absorption (DBP, mL/100 g) is a quick guide to how much a grade will thicken the formulation. Compare VS3550U at 140–160 mL/100 g, chosen to keep UV viscosity down, with VS3851 at 340–360 mL/100 g.
- Pore volume (mL/g) indicates matting per gram: higher pore volume usually means more particles at the same weight.
- Loss on ignition (%) reflects surface treatment level. VS651 at 4.48% and VS660 at 8.25% have similar particle size but different surface chemistry.
The full values for every grade are on the technical data sheets page.
A practical screening approach
- Define the target. Record gloss and the angle it is measured at (60° for most matt finishes, 85° when gloss at 60° is very low), the dry film thickness, the substrate and the application method.
- Pick a lead and a comparison grade. Screening two grades side by side against your current control shows more than a single grade at several loadings.
- Run a loading ladder. Prepare a few addition levels for each grade so you can see where gloss levels off and where viscosity or appearance starts to suffer.
- Keep dispersion constant. Use the same mixing time and energy for every sample; under- or over-dispersion changes gloss and can shift results between batches.
- Judge more than gloss. Check clarity or colour, surface uniformity, feel, scratch and burnish resistance, recoatability, and viscosity and settling after storage.
Common pitfalls when changing matting agent
- Comparing at equal weight only. Grades with different pore volume and particle size do not matt equally per gram, so compare at equal gloss as well as at equal loading.
- Ignoring film thickness. A grade that works at one film build can look rough in a thinner film or under-matted in a thicker one.
- Skipping storage tests. Hard settling or slow viscosity rise can appear only after days or weeks, especially with untreated grades in low-viscosity systems.
- Assuming a treated grade is always better. Surface treatment helps settling and feel, but it can affect intercoat adhesion in some resins, so test it in your own system.
Where to start
The fastest way to a shortlist is to start from the system: resin type, cure method, target gloss and angle, film thickness and application method. The grade selector filters Vistamatt grades by application and gloss direction and suggests a lead and comparison grade to test against your current control. If you would like lab samples for a screening round, you can request them through the contact page.